Making a Thermoelectric Generator (TEG)

A thermoelectric generator (TEG) is a kind of "free energy device" which has the property of converting temperature into electricity. In this post we learn a little about this concept and find out how we can use it to generate electricity from heat and cold.

What's TEG


In one of my earlier articles I have already explained a similar concept regarding how to make a small refrigerator using a Peltier device

A Peltier device is also basically a TEG designed for generating electricity from a difference of temperature. A thermoelectric device is quite similar to a thermocouple, the only difference being in the composition of the two counterparts.

In a TEG two different semiconductor materials (p-n) are used for the effect whereas a thermocouple works with two dissimilar metals for the same, although a thermocouple might require a substantially larger difference of temperature compared to the smaller TEG version.

Also popularly known as the "Seebeck" effect, it enables a TEG device to initialize the generation of electricity when subjected to a difference of temperature across its flip sides. This happens due to the specially configured internal structure of the device which utilizes a couple of doped p and n semiconductors for the process.

The Seebeck Effect


According to the Seebeck principle when the two semiconductor materials are subjected to two extreme temperature levels, initiates an electron movement across the p-n junction resulting in the development of a potential difference across the outer terminals of the materials.

Although the concept appears to be amazing, all good things come with an inherent drawback and in this effect too their is one which makes it relatively inefficient.

The need of extreme difference in temperatures across its two sides becomes the most difficult part of the system, because heating up one of the sides also implies that the other side would also heat up which would eventually result in zero electricity and a damaged TEG device.

In order to ensure an optimal response and for initiating the flow of electrons, one semiconductor material inside the TEG needs to be hot and simultaneously the other semiconductor needs to be kept aloof from this heat by ensuring a proper cooling from the counter side. This criticality makes the concept a little clumsy and inefficient.

Nevertheless, the TEG concept is something which is exclusive and not feasible using any other system so far, and this uniqueness of this concept makes it much interesting and worth experimenting with.

TEG Circuit using Rectifier Diodes


I have tried to design a TEG circuit using ordinary diodes, although I am unsure whether it will work or not, I am hoping some positive results could be achieved from this set up and it has a scope for improvement.





Referring to the figures we can witness a simple diode assembly clamped with heasinks. The diodes are 6A4 type diodes, I have selected these bigger diodes in order to acquire larger surface area and better conduction rate.



Diode 6A4

The simple thermoelectric generator circuit set up shown above could be possibly used for generating electricity from waste heat, by suitably applying the required degrees of heat difference across the indicated heat conducting plates.

The right side figure shows many diodes connected in series parallel connections for achieving higher efficiency and proportionately higher accumulation of potential difference at the output.

Why Use a Diode for Making a TEG




I have assumed that diodes would work for this application since diodes are the fundamental semiconductors units consisting of a doped p-n material embedded within their two terminating leads.

This also implies that the two ends are specifically composed of the diverse materials facilitating easier application of temperature separately from the two opposite ends.

Many such modules could be built and connected in series parallel combinations for achieving higher conversion rates, and this application could be implemented using solar heat also. The side which needs to be cooled could be achieved through air cooling or through an enhanced evaporative air cooling from atmosphere for increasing the efficiency rate.

Need Help? Please send your queries through Comments for quick replies!




Comments

mark kim blando said…
Hi hello sir swagatam..this heat and cool you write above is atouched to the anode(cool) and cathode (heat) ?
mark kim blando said…
Im so interested of this new thermoelecric generator sir..thanks again and again
Swagatam said…
Hi Mark, the heat difference can be applied anyway round, the response will be either the generation of positive current or negative current depending on how the heat is polarized
mark kim blando said…
Ah ok sir I got it..thank you alot sir swagatam..days I found your website I learned alot f your ideas.God bless you more sir swagatam
Swagatam said…
you are welcome Mark!

Contact me for Customized Circuits

Name

Email *

Message *


 Follow on G+  Follow on Facebook   Follow on Tweeter  Follow on G+  Follow on G+