Skip to main content

Simple 50 Watt Power Amplifier

A simple 50 watt amplifier circuit is explained below, let's learn how to build it at home using this versatile single amplifier chip LM3876T

By: Dhrubajyoti Biswas

Analyzing the Circuit

A good power amplifier is a necessity, especially when it comes to listening music. An amplifier added to a sound system will definitely enrich the quality of music. This project therefore will attempt to give you a detailed insight of making a simple 50 watt power amplifier.

The system that we are going to deal with is primarily based upon the technical specification laid out by National Semiconductors, and following this the result came out well. Easy to build and good output in terms of distortion and noise, the following section will detail the way it is built.

Before we kick-start this development, we have tested the PCB and result came out positive. We have received very good sound quality provided the protection circuitry is not in operational mode.

The last stable version of the board ESP P19 (Rev-B) has few alterations, such as, the connection to the sound impairment monitor [SIM] has been taken out.

The following Figure is a layout of the original board:

Board Layout



Simulation and Working


As per the diagram, there is an addition of polyester bypass capacitors and the mute circuit is left disabled, since it is mainly useful when developing a preamp. However, we made some adjustment into the board to provide space for power and input connectors.

As per the above figure, the voltage gain is set to 27dB, and it can be changed by adding resistors of different value for the path of the feedback.

The inductor has 10 turns of enameled copper wire of 0.4mm and is wounded around the body of the 10ohm resistor. The soldered wire lies at the end of the resistor and the insulation should be brushed off on each end.

Our recommendation would be to use 1watt type 10ohm and 2.7ohm resistors. The rest should metal film of 1%. It is also ideal to keep the electrolytic capacitors @ 50V.

For supply, 100nF (0.1uF) should be placed near to the IC in order to avoid oscillation. The voltage supplies to maintain at full load should be around +/- 35 volts, which would produce 56 watts (Max.).

Also to achieve lowest case to the heatsink thermal resistance it is vital to engage max power. This can be done by mounting mica washer with no insulation. However, do keep in mind the heatsink need insulation from the chassis since the heatsink maintain supply voltage of –ve.

The following schematic in Figure shows the changes we made on the original board:



Referring to Figure above, the revised board is very much similar to that of the original one, except some changes by removing some components along with the SIM.

The present on-board decoupling gives great performance. It uses electrolytic of 100nF Polyester and 220uF electrolytic.

Alternatively, you can also use monolithic ceramic capacitor on every rail. While C1 and C2 is referred as polarized electrolytic types, you may use non-polarized electros.

Another option would be to apply on C1 a 1uF polyester cap. If C1 is intended to be used as tweeters you can use small values of 100nF which is good to go ahead.

If you are building the proposed simple 50 watt power amplifier circuit to use it for biamped/triamped system tweeter or midrange, the C1 valued need to be reduced to 100nF (3dB @ 72Hz).

Also you can use 1uF polyester at the rate of -3dB @ 7.2Hz in case of any general use. However, this adjustment would increase the performance of the bass and you can also apply any value till 10uF (approx.) on C1 if needed to do so.

The new design of the PCB facilitates using the amp as dual-mono. You can split the PCB track while each individual has its own power supply.

While the IMO carries less point, this enables cutting the PCB in half with each halves has its own supply. The board gives the facility to make output connection to the PCB pins, or by using PCB mount spade lug.

Upgrading the Design


As per the board’s design shown in the figure, you can use LM3886. It is very much identical and moreover the specification is higher.

The PCB also have the provision to connect pin number 1 and 5. Furthermore, you can also use the board as a bridge in case of LM3886 to achieve 120W into 8ohms. Our suggestion would be to use P87B to enable out-oh-phase signal that is needed to operate BTL.

To run an amp as inverting is a common occurrence, but doing that ends up with low impedance to the preamp, which may give trouble as you may find distortion or problem in loading. Therefore, it is always safe to drive the amplifiers, since the P87B can drive each amp individually.

Whereas parallel operation is often a common suggestion when building this system, our experience in this domain does not recommend the same.

The requirements for gain tolerance during parallel operation is very strict as you need to ensure the amplifier matches 0.1% or keep it over the entire bandwidth.

Now since the impedance of the IC has low output, therefore even 100mV may end up generating high circulating currents via the IC’s. As 0.1Ω comes as usual suggestion, a mismatch of 100mV may end up 0.5A of circulating current, which ends up in overheating.

Pinout Diagram



Figure above shows the IC pinouts for LM3876 where the pins are staggered to enable the PCB tracks run into the pin of the IC. The LM3886 on the other hand is very much identical to the former, and it can be used by adding little more power, if needed.

However, the only difference that lies between the two is in LM3886 it is mandatory for Pin 5 to connect to +ve supply.

The PCB used for this amp is mainly meant for stereo amplifier. It is single-sided with the location of supply fuse in the PCB. The stereo board contain small four fuses (115mm x 40 mm).

Overall the revised board as in Figure 1.1 is of the same size to that of the original (as shown in Figure 1.0) and we have applied similar spacing in between the IC’s to facilitate retro-fitting, if needed.

However, as a caution do keep in mind to use heat-sink for this project as the system gets really hot within a short time, which may end up destroying the things from overheating.

Need Help? Please leave a comment, I'll get back soon with a reply!




Comments

  1. hi i need a power amplifier with gain 10 will you help me to find the circiuts

    ReplyDelete
  2. you can try the first circuit from this article

    https://homemade-circuits.com/2012/08/ic-lm-386-datasheet-explained-in-simple.html

    ReplyDelete

Post a Comment