The previous post explained how a DC content after rectification may carry the maximum possible amount of ripple voltage, and how it may be reduced significantly by using a smoothing capacitor.

Although the final ripple content which is the difference between the peak value and the minimum value of the smoothed DC, never seem to eliminate completely, and directly relies on the load current.

In other words if the load is relatively higher, the capacitor begins losing its ability to compensate or correct the ripple factor.

## Standard Formula for Calculating Filter Capacitor

In the following section we will try to evaluate the formula for calculating filter capacitor in power supply circuits for ensuring minimum ripple at the output (depending on the connected load current spec).**C = I / 2 x f x Vpp**

where I = load current

f = input frequency of AC

Vpp = the minimum ripple (the peak to peak voltage after smoothing) that may be allowable or OK for the user, because practically it's never feasible to make this zero, as that would demand an unworkable, non-viable monstrous capacitor value, probably not feasible for anybody to implement.

Let's try to understand the relation between load current, ripple and the optimal capacitor value from the following evaluation.

### Relation Between Load Current, Ripple, and Capacitor Value

In the mentioned formula we can see that the ripple and the capacitance are inversely proportional, meaning if the ripple needs to be minimum, the capacitor value needs to increase and vice versa.

Suppose we agree to a Vpp value that's, say 1V, to be present in the final DC content after smoothing, then the capacitor value may be calculated as shown below:

**Example:**

**C = I / 2 x f x Vpp**(assuming f = 100Hz and load current requirement as 2amp))

*Vpp should be ideally always a one because expecting lower values can demand huge unpracticable capacitors values, so "1" Vpp can be taken as a reasonable value.*

Solving the above Formula we get:

**C = I / 2 x f x Vpp**

= 2 / 2 x 100 x 1

= 0.01 Farads or 10,000uF (1Farad = 1000000 uF)

Thus, the above formula clearly shows how the required filter capacitor may be calculated with respect to the load current and the minimum allowable ripple current in the DC component.

By referring to the above solved example, one may try varying the load current, and/or the allowable ripple current and easily evaluate the filter capacitor value accordingly for ensuring an optimal or the intended smoothing of the rectified DC in a given power supply circuit.

**Need Help? Please send your queries through Comments for quick replies!**

## 18 Comments

Nice post sir really useful information.

ReplyDeletethanks Vijay, I am glad you liked it....

ReplyDeleteSir, I have seen more number of inverter circuits on your site. Can u suggest the circuit which should produce an exact sinewave as same grid supply.

ReplyDeletenice post sir.really helpful..... thanks sir

ReplyDeleteDear Sir,

ReplyDeleteFor SMPS (step down) out put capacitor calculation whether we have to take switching frequency as "f" in the formula? please clarify

Vijay, trying to acquire an analogue sinewave replication can make an inverter inefficient, that's why all inverers rely on PWM which is much suited with digital inverters and are able to deliver max efficiency... and also a waveform quite similar to a pure sine wave.

ReplyDeleteDear Raveesh, in SMPS, the waveform is rectangle or square and also the duty cycle factor is present...so may be the "F" could be differently expressed here in terms of duty cycle %....not much sure about it right now...

ReplyDeleteIt's my pleasure Alamgir

ReplyDeleteSir I planned to design an inverter for my home which should light up 3,20 watt cfl bulb and also for mobile charging.hence I assumed that my total watt requirement is not more than 100watt.please suggest any circuit based on my requirement and say the information about the battery that I need to use for operating an inverter for 5 hours.

ReplyDeleteVijay, you can try the following circuit:

ReplyDeletehttps://homemade-circuits.com/2012/09/mini-50-watt-mosfet-inverter-circuit.html

the battery should be rated at at least 12V, 75 AH

the inverter is capable of handling up to 200 watts if the trafo is appropriately rated

Sir output of my transformer after rectification is 11.9v I want to charge my 12v battery please suggett the capacitor rating I want to use here to charge my battery please reply fast

ReplyDeleteVijay, if you are interested t calculate the exact value of the capacitor then you'll need to evaluate charging current first, which can be found by dividing the AH of your battery with 10.

ReplyDeleteIn general you can simply use the highest value capacitor that may be feasible for you.

A very good post that I have learnt a lot. Please how do we measure/calculate/obtain the Vpp?

ReplyDeleteI am glad you liked!!

ReplyDeleteVpp is the final ripple that may appear with the DC after rectification, and it is supposed to be zero ideally, but in the practical world a zero ripple cannot be possible, and moreover that would demand a huge filter capacitor...therefore we assume this value to be around "1" for all filter capacitor calculations

Thank you so much for your clarification. You have helped so much.

ReplyDeleteYou are welcome!!

ReplyDeletevery good post and site

ReplyDeleteand about calculating filter capacitor voltage what's your idea?

Thank you Jack!

ReplyDelete