Skip to main content

Stereo FM Transmitter using IC BA1404

The following posts explains how to build a simple to build FM stereo transmitter circuit using IC BA1404.

About the IC BA1404


An exceptional stereo audio FM wireless transmitter circuit is presented below.

The circuit relies upon the IC BA1404 from ROHM Semiconductors.

BA1404 is a monolithic FM stereo modulator which includes integrated stereo modulator, FM modulator, RF amplifier circuitry.

The FM modulator could be controlled from 76 to 108MHz and power source for the circuit could be nearly anything between one.25 to three volts.

Simulation and Working


In the circuit R7, C16, C14 and R6, C15, C13 makes the pre-emphasis system for the right and left stations respectively.

This is achieved for complementing the frequency response of the FM transmitter with the FM receiver.

Inductor L1 and capacitor C5 is employed to fix the oscillator frequency. Group C9,C10, R4,R5 enhances the station splitting up.

38kHz crystal X1 is linked between pins 5 and 6 of the IC. Composite stereo reception is formed by the stereo modulator circuit employing the 38kHz quartz regulated frequency.

Construct the circuit on a high quality PCB.

Operating the circuit from a battery pack minimizes disturbances.

Work with an 80 cm copper cable as antenna.

For L1 try to make three turns of 0.5mm dia enamelled copper wire on a 5mm dia ferrite core.

Stereo FM Transmitter Circuit Diagram


 



Need Help? Please leave a comment, I'll get back soon with a reply!




Comments

  1. Can this circuit transmit up to 2km? I also want to design mobile Phone call jammer can u pls upload the circuit or show me the link to mobile call jammer circuit. Thanks

    ReplyDelete
  2. I have neither a ferrite core nor a variable inductor. Please post a way to use a static inductor with a 2-18pf variable capacitor.

    ReplyDelete
  3. ...ferrite cored inductor is a must for the explained design

    ReplyDelete
  4. ok...made this circuit...but getting too much static. What do you think is the culprit?

    ReplyDelete
  5. Wait. I just found a 5mm ferrite core. But since I don't have 0.5mm copper wire. Would you please tell me the improvised version of this coil for SWG22 wire. I can make air core coils according to given values but I don't know how ferrite cores change the inductance value so please tell me how to make a coil with 5mm ferrite core using SWG22..Hope this will eliminate the static caused by my circuit.

    ReplyDelete
  6. Please tell me how make this inductor for 22SWG as 0.5mm copper wire isn't available in my city. SWG22 is 0.711mm wide. I have salvaged a 5mm ferrite core. How many turns should I make to use it as an inductor in this circuit?

    ReplyDelete
  7. 0.5mm is not critical you can use any other gauge thicker than that....
    use 5 turns initially

    ReplyDelete
  8. to prevent noise use PCB with grounded tracks

    ReplyDelete
  9. yes it must be ground filled type or "copper pour" type PCB to enahnce stability.

    sorry I cannot check your PCB if it's posted in some other electronic website.

    you can post in some free image hosting site, and send the link here

    ReplyDelete
  10. Wait then i'm sending the link to ground fill pcb pdf and the silkscreen too....
    This is the link to the shared folder on google drive:
    https://drive.google.com/drive/folders/0B-5jjw-tjYplaGJuVjN5cGUxOWc?usp=sharing

    ReplyDelete
  11. You said 5 turns initially, if I don't get correct transmission, should I increase or decrease the number of turns?

    ReplyDelete
  12. you will have to experiment with the turns because the original IC datasheet has not informed about the exact number of turns for the coil

    ReplyDelete
  13. Made this as you instructed....still not getting a clear reception and the audio transmission isn't recognizable. What should I do?

    ReplyDelete
  14. check the datasheet of the IC and see if there's any refinements to be done.

    ReplyDelete
  15. Checked it...The datasheet didn't help much....

    ReplyDelete
  16. that's quite long and sufficient...not sure, there could some other hidden issue somewhere

    ReplyDelete
  17. OK, good, thanks for updating the info

    ReplyDelete
  18. Hello i got this IC but I used a different circuit and its not working out as expected in the first place how do I know the value of the frequency that is being transmitted?

    ReplyDelete
  19. Can I connect this circuit to the TV output Audio RCA connectors

    ReplyDelete
  20. Hello, It would be difficult for me to troubleshot without practically checking it...
    you can check the frequency by capturing the transmission on any standard FM radio and then checking the frequency level on the tuning calibration of the radio.

    ReplyDelete
  21. it's for radio FM range....won't work for TV I guess...

    ReplyDelete
  22. though i would suggest creating an LCR meter using arduino..It is an easy build and helps to find transmission frequency.

    ReplyDelete
  23. What is the software for doing the simulation BA1404?

    ReplyDelete
  24. Sunirnay ChatterjeeFebruary 17, 2018 at 5:28 PM

    i made a BA1404 Stereo FM Transmitter but unable to found stereo FM receiver circuit . Please help me as soon as possible.

    ReplyDelete
  25. you can use your mobile phone's FM radio...

    ReplyDelete
  26. Hello Sir, I Like This Circuit, And I Want To Construct It, But I Have Some Questions To Ask
    1. For Instance If I Dont Get 38khz Crystal Oscillator, Can I Generate 38khz From 555 Timer And Feed It To The Circuit? And Can It Work Normal Like For Crystal Oscillator?
    2. Can It Be Modified By Adding Press Botton For Scanning Or Selecting The Frequency?
    3. Can We Add A Power Indicator Led To It?
    4. Can It Be Modified By Adding Sound Indicator Circuit To It?

    ReplyDelete
  27. Solomon, we use crystal to ensure extremely stable frequency which cannot be achieved using ICs like 555, so it might not work.
    You may have to refer the datasheet of the IC to learn if any modifications may be possible or not externally.
    Music level indicator can be added at the output side of the circuit

    ReplyDelete

Post a Comment