High Current Mosfet IRFP2907 Datasheet

The post explains the main features datasheet of high current N-Channel mosfet IRFP2907 which is rated to handle up to a staggering 209 amps of continuous current at a reasonably massive 75 volts.

High Current Specs


With the advent of mosfets, switching huge power through compact packages has become particularly feasible.

Take for example the proposed high current mosfet IRFP2907 (has no relation to 2N2907) which could be used for triggering currents exceeding 200 amps, exclusively suitable for wind turbine generators. application

Although this device is designed specifically for automotive applications, the extreme range of this device can be effectively employed for many other applications such as inverters, wind turbines, soar inverters etc.

Precisely, this N-Channel device would be ideally suited for wind turbine inverter applications since this application incorporates alternators which is an automotive component.

Main Specifications and Features


 



 

Let's learn about the main features of the mosfet IRFP2907

  1. Advanced Process Technology: ensures a rugged foolproof design and operation parameters.

  2. Ultra Low On-Resistance: allows optimal delivery of the source current across the load thereby enhancing the overall efficiency of the system.

  3. Dynamic dv/dt Rating: makes the unit extremely desirable with high power critical systems.

  4. 175°C Operating Temperature: this extreme range allows better sustaining, and consistency even under stressful operating conditions

  5. Fast Switching: Makes the device specifically suitable for rapid high current switching applications without the fear of device breakdown yet with maximum efficiency.

  6. Repetitive Avalanche Allowed up to Tjmax: Avalanche current is no more an issue with this device which is well guarded to make it completely failproof even under worst case scenarios.


Technical Datasheet


The Datasheet of the High Current Mosfet IRFP2907 may be understood with the following points:

  1. Extremely Low RDS(on) = Typically around 4.5 milliOhm, that's almost zero resistance across the drain and the source terminals when the device is fully saturated.

  2. Saturating Voltage = The saturating voltage VGS is around 10V which may be exceeded to not more than 20V. Applying this range of voltage across the gate and the source terminals would allow full saturation and almost zero resistance across the drain/source terminals.

  3. High Switching Current: With the above parameters applied, the maximum allowable current across the drain and the source terminals would be anything up to 200 amps....that's huge.

  4. Breakdown Voltage = It should not be exceeded preferably above 70 volts. This is applied across the drain and the source with a load in series at current levels that may exceed the 200 amp mark, as explained above.

Need Help? Please send your queries through Comments for quick replies! And please Bookmark my site :)




Comments

oliver oliveros said…
Hi Sir Swagatam,

I have a busted GTI. I would like to know if i can replace the mosfet with another brand of N-Channel?

original Mosfets:
HY1906
65V/130A

Swagatam said…
Hi OLiver, yes that can be done.
oliver oliveros said…
can i use this mosfet (IRFP2907) for replacement?

Thanks sir
Swagatam said…
yes the specs match, so it can be tried
Hi sir, can I use IRFP2907 in place of hy1906 or other suggestions
Swagatam said…
Hi Shahnawaz, please check the datasheets of the two fets and check what voltage and current these are rated for...and then you can judge yourself whether or not these are interchangeable.
Kanji Mandaviya said…
Hello sir, can I make a circuit for motor reverse and forward rotation for few time base
Swagatam said…
Hi Kanji, yes you can by using a 4060 IC
kassimdandago said…
If you use two 2907 with a center tapped transformer & big heat sink, can it tolerate or replace arrangements of 50N06 ie each 2907 =6, 50N06, please highlight.
Swagatam said…
what is the specifications of 50N06?? if 2907 is 6 times higher than 50N06 then yes your assumption may be correct, it can be replaced with a single 2907 having a calculated large heatsink.
luis villaflores said…
hi sir can i replace a chinise mosfet hy1906 with the available mosfet like irf3205 nedd help please??
Swag said…
Hi Luis, you can do it, but make sure the voltage and current specs of your mosfet is not less than the original mosfet.

Contact me for Customized Circuits

Name

Email *

Message *


 Follow on G+  Follow on Facebook   Follow on Tweeter  Follow on G+  Follow on G+

Follow Homemade Circuits