Skip to main content

15V 10 Amp Voltage Regulator Using IC LM196

The following article explains a linear voltage regulator power supply circuit using the IC LM196 which is capable of handling up to 10 amps of current and is able to provide a variable voltage right from 1.25V to 15V DC.

About the IC LM196 or LM396


The IC LM 196 is single chip versatile, high performance regulator device which can be configured to provide an adjustable voltage output of 1.25V to 15V or even further at currents in excess of 10 amps.

It is a single chip solution for all electronic circuit applications which involve or require regulated DC up to 10 amps.

That means now you can carry on heavy duty voltage operations as per your personal preference using this easy to build single chip circuit

Many of my earlier posts have discussed circuits involving a similar IC, the LM338, which is also capable of providing similar features, but cannot handle above 5 amps, the LM196 on the other hand overcomes this limitation of LM338 and goes further by adding 5 amps more to the specs.

Main Specifications


The main features of this adjustable 15V 10 amp voltage regulator IC may be summarized as follows:

  1. Output custom tailored at +/-0.8V

  2. Minutely adjustable voltage right from 1.25V to 15V DC

  3. Guaranteed output current that's not below 10 amps

  4. Verified with P+ product enhancement testing

  5. Maximum power dissipation not exceeding 70 watts even at full load.

  6. Output internally protected against over load and short circuit

  7. Device internally protected against thermal run away or thermal break down situations.

  8. Output voltage supply guaranteed even under worst case scenarios such as adjustment pin disconnected.

Pin out details of LM196


As given in the following diagram, from bottom with the larger area of the metal downward, the pin outs of the IC LM196 may be identified as follows:

  1. Right pin = Adjustment pin

  2. Left Pin = Output pin.

  3. Case or Body = Input


10 Amp Power Supply Circuit Using IC LM196 or LM396


The standard 10 amp voltage regulator circuit diagram using the IC LM196 can be witnessed in the following figure.

The calculations of the resistors are similar to that of IC LM338 or LM317. R2 may be adjusted to get the required regulated voltage at the output.

All the ground terminals involved in the circuit must be fixed with the main input ground which will be obviously the negative point of the bridge rectifier (not shown here). Similarly, the positive to the load must be directly acquired from the relevant lead of the IC.

The ground and the positive is taken from the main nodes due to the involvement of high currents with the circuit. As current increases, the conductor proportionately offers more resistance to the flow of the current which results in voltage drops at the output and hence  unnecessary lengths of tracks should be avoided.

10 amp variable regulator using LM 196, LM396 IC





Need Help? Please leave a comment, I'll get back soon with a reply!




Comments

  1. I want to make a power supply that runs 5 pc exhaust fans, so refer me power supply circuit...
    and to receive 5 amp in the above mentioned circuit, how much amp transformer is needed?

    ReplyDelete
  2. Please specify the voltage and amp rating of the fans so that I can calculate the total power required from the power supply.

    You can use LM338 in place of LM196 which would give you exactly 5amps, the IC would require a heatsink strictly.

    ReplyDelete
  3. am looking for a voltage regulator of 15volts 16 amps but I cant get it any suggestion.

    ReplyDelete
  4. you can put 4 LM338 IC in parallel and get the desired regulation from the configured circuit.

    ReplyDelete
  5. Hi swagatam I need a circuit that can cut off output of inverter 220v a.c on short circuit or over load protection pls

    ReplyDelete
  6. Hi Ajeet, you can refer to the following links,and select the one as per your requirement

    https://homemade-circuits.com/?s=overload

    ReplyDelete
  7. Hi sir, can you help me? I need a circuit with 12v and 10a max output, but the input is an solar panel with 30v and 15a max.

    Thank you, salutes from Brazil.

    ReplyDelete
  8. Hi Dinilton, you can try the following concept and modify it accordingly as per your circuit specifications

    https://www.homemade-circuits.com/5v-pwm-solar-battery-charger-circuit/

    ReplyDelete

Post a Comment