Skip to main content

Make a Room Air Ionizer

In this article we learn how to build a simple room ionizer circuit for getting a clean, pollution free environment right inside our home.

Introduction


Have you ever thought or wondered why atmosphere over hill stations and other similar places which are far away from modern cities give you a feeling of  freshness and good health?

The answer is simple, the air in such places are free from pollutants and  harmful chemicals like smoke and gases.

Well, if you are settled in one of those cities which is engulfed with bad air and if you have compromised with the situations, here's your chance to get rid of the situation through the circuit explained below:

An air ionizer or  as some may refer it as a room ionizer is basically a device or electronic circuit which is designed for generating voltage at the level of kilo-volts for implementing the said ionizing effects. So what's ionizing after all?

The high voltage that's generated from an ionizer is actually tuned for generating a negative voltage, at around minus 4 kV. This high negative voltage is allowed to get terminated over an open ended sharp conductor tip or point that's sharply carved.

When the voltage reaches at this sharp point, it tends to continue its forward motion and gets shot or released into the air in the form of negatively charged ions.

Once in the air these ions become free to move around and start getting dispersed across the room or the premise, as more and more ions are released from the air ionizer device.

Now as these ions roam freely in the air it comes across and starts colliding with the already present pollutants like dust particles, smoke/gas particles etc in the air.

As per the rules all particles and all materials present around should be positively charged, so what happens, the oppositely charged ions starts collecting these pollutants from the air by attracting them toward them (opposites attract), just as a magnet bar would do to iron pins.

The pollutants in the air slowly find themselves pulled and firmly stuck over these ions until each of the ions become so much pollutant laden and heavy that they start crashing on the ground or if they find a wall nearby they start gathering on it.

In this way the air in the course of time becomes absolutely clean and free from all impurities.

Simulation and Working


The circuit is quite simple and can be built even by a layman, having just basic knowledge of electronics.

The circuit is fundamentally based on Cockroft-Walton Ladder Network, The concept makes use of a network of many diodes and capacitors arranged in such a way that the applied voltage to it gradually becomes stepped up to very high levels, in the order of around 10kV,

However a 10kV range is not suitable for the discussed ionizing effects, in fact at this level the effect might produce opposite results.

If we go by calculations the present design would also generate around -10kV, spoiling the intended cause, however practically it is found to be dropping to about -4kV.

This reduction happens due to radiation losses, because in the course of its stepping up, the voltage tends to spark through emissions across the PCB until finally the resultant voltage at the output tip of the device reaches only up to around -4kV which is by God's grace the exact level for achieving the ionizing effect.

Circuit Diagram


 



 

The entire circuit may be built over a general purpose board, by soldering the shown number of capacitors and diodes exactly in the way they are arranged in the diagram.

Following the diagram pattern would make the making easier to assemble and would produce guaranteed results without faults.

After the circuit is assembled, check the entire board for any wring connections, this is important because the circuit is very critical with its polarities, a single wrongly connected diode would make the results zero.

After proper confirmation, the soldered side should be thoroughly cleaned with thinner so that no residual flux stays deposited causing loss of voltage and reduction in the desired effects.

The end which is terminated for releasing the ions must be needle shaped, preferably a small pin or needle can be used there for enabling perfect prorogation of the ions.

After all the above precautions are complete, it's time to power the unit. Be extremely careful, as the entire circuit is connected directly with mains AC and can be life threatening if touched in the powered position.

Verifying the Working of the Circuit


Once the circuit and if hopefully everything is rightly done with the assembly, you would hear a "hissing" noise near the tip of the releasing pin point. The area near the tip of the pin would give you a cooler sensation like a cool breeze flowing out.

The point would also produce a fish like smell.....all the above indications would confirm that the unit is working right and you are already breathing fresh air around your nose and heading toward a healthy life.

THE ABOVE CIRCUIT WAS SUCCESSFULLY BUILT AND TESTED BY ONE OF THE KEEN FOLLOWERS OF THIS BLOG, MR. ALI ADNAN.

THE FOLLOWING BEAUTIFUL PICTURES WERE SENT BY HIM, LET'S ENJOY THEM.

Prototype Pictures


 



 



 



 

Need Help? Please leave a comment, I'll get back soon with a reply!




Comments

  1. Hi everybody

    Want to see the simulation for this project?

    Copy the long long link below, and paste in browser's address bar.

    A java applet window will be opened, maximize it.

    Close the switch at the top left and see the voltage going in -kV in the graph at the bottom.

    Enjoy !!!

    www.falstad.com/circuit/#%24+1+5.0E-6+10.20027730826997+50+5.0+50%0Ar+176+48+176+224+0+1000000.0%0Ar+224+48+224+224+0+1000000.0%0Ac+224+48+272+48+0+1.0E-8+9.999987702542512E-4%0Ad+272+48+224+224+1+0.805904783%0Ad+288+224+272+48+1+0.805904783%0Ad+336+48+288+224+1+0.805904783%0Ad+368+224+336+48+1+0.805904783%0Ad+400+48+368+224+1+0.805904783%0Ad+432+224+400+48+1+0.805904783%0Ad+464+48+432+224+1+0.805904783%0Ad+496+224+464+48+1+0.805904783%0Ad+528+48+496+224+1+0.805904783%0Ad+560+224+528+48+1+0.805904783%0Ad+592+48+560+224+1+0.805904783%0Ad+624+224+592+48+1+0.805904783%0Ad+656+48+624+224+1+0.805904783%0Ad+688+224+656+48+1+0.805904783%0Ad+720+48+688+224+1+0.805904783%0Ac+224+224+288+224+0+1.0E-8+9.999989198092862E-4%0Ac+288+224+368+224+0+1.0E-8+9.999990116966728E-4%0Ac+368+224+432+224+0+1.0E-8+9.999991506219885E-4%0Ac+432+224+496+224+0+1.0E-8+9.999993073961377E-4%0Ac+496+224+560+224+0+1.0E-8+9.999993337146407E-4%0Ac+560+224+624+224+0+1.0E-8+9.999994182123828E-4%0Ac+624+224+688+224+0+1.0E-8+9.999995329792455E-4%0Ac+272+48+336+48+0+1.0E-8+9.99998885021114E-4%0Ac+336+48+400+48+0+1.0E-8+9.999989554501099E-4%0Ac+400+48+464+48+0+1.0E-8+9.999990132598668E-4%0Ac+464+48+528+48+0+1.0E-8+9.999991021345522E-4%0Ac+528+48+592+48+0+1.0E-8+9.999992198004293E-4%0Ac+592+48+656+48+0+1.0E-8+9.99999331440904E-4%0Ac+656+48+720+48+0+1.0E-8+9.99999449192046E-4%0Aw+688+224+688+288+0%0Ac+688+288+624+288+0+1.0E-8+9.99999464454504E-4%0Ac+624+288+560+288+0+1.0E-8+9.999995556881913E-4%0Ac+560+288+496+288+0+1.0E-8+9.999996321710114E-4%0Ac+496+288+432+288+0+1.0E-8+9.999997343470568E-4%0Ac+432+288+368+288+0+1.0E-8+9.999998254670572E-4%0Ac+368+288+304+288+0+1.0E-8+9.999998571288415E-4%0Ac+304+288+240+288+0+1.0E-8+9.999999532226411E-4%0Ac+656+432+592+432+0+1.0E-8+9.999994042289018E-4%0Ac+592+432+528+432+0+1.0E-8+9.999994771590082E-4%0Ac+528+432+480+432+0+1.0E-8+9.999996160843239E-4%0Ac+480+432+400+432+0+1.0E-8+9.999997990064458E-4%0Ac+400+432+336+432+0+1.0E-8+9.999998376599706E-4%0Ac+336+432+272+432+0+1.0E-8+9.999999281546934E-4%0Ac+272+432+208+432+0+1.0E-8+0.0010000000340539827%0Ad+624+288+656+432+1+0.805904783%0Ad+592+432+624+288+1+0.805904783%0Ad+560+288+592+432+1+0.805904783%0Ad+496+288+528+432+1+0.805904783%0Ad+432+288+480+432+1+0.805904783%0Ad+368+288+400+432+1+0.805904783%0Ad+304+288+336+432+1+0.805904783%0Ad+240+288+272+432+1+0.805904783%0Ad+208+432+240+288+1+0.805904783%0Ad+272+432+304+288+1+0.805904783%0Ad+336+432+368+288+1+0.805904783%0Ad+400+432+432+288+1+0.805904783%0Ad+480+432+496+288+1+0.805904783%0Ad+528+432+560+288+1+0.805904783%0Ad+192+288+208+432+1+0.805904783%0Aw+720+48+720+432+0%0Aw+720+432+656+432+0%0Ac+240+288+192+288+0+1.0E-8+0.0010000000291654487%0Ar+160+560+320+560+0+3300000.0%0Ar+320+560+544+560+0+3300000.0%0Ar+544+560+784+560+0+3300000.0%0Aw+784+560+784+352+0%0Aw+192+288+160+288+0%0Aw+160+288+160+560+0%0Aw+224+224+176+224+0%0Aw+176+224+128+224+0%0Aw+224+48+176+48+0%0As+128+48+176+48+0+1+false%0Av+128+112+128+160+0+1+50.0+220.0+0.0+0.0+0.5%0Aw+128+160+128+224+0%0Aw+128+112+128+48+0%0Ao+68+64+0+35+2560.0+9.765625E-5+0+-1%0A

    ReplyDelete
  2. May I ask a question? 1M resister is essential or not?
    (Because I did not check 1M, it is not availiable right now.)

    ReplyDelete
  3. Actually there should be a neon bulb in series with the 1M, by mistake it's not shown in the diagram.

    You can remove it anyway, if you wish!

    ReplyDelete
  4. Hi Swagatam,

    Is it possible to incorporate a flow of ionised "air" in this circuit(Like a small fan or something)? I work with some plastic products, so flushing it a small stream of ionised air would be useful.

    Thank you.

    ReplyDelete
  5. Hi Jithin,

    I am sure if ions could be pushed with breeze, however since ions too have mass they could be influenced with air flow, ......you can try it.

    ReplyDelete
  6. Hi Swagatam,

    i have made this circuit. I could not smell any thing near it, could not see sparks on pin top in the dark , and no sound. but when i place my tester near to pin a small sparks shows in the dark. Is my circuit ok? Is there any ions produced from pin??

    Thank You

    ReplyDelete
  7. Hi Rakibul, is the tester glowing when the tester is around 1cm near the needle without direct contact? If yes then your circuit may be alright and in this situation you should also get the fishy smell very close to the needle....... and under perfect silence you would also hear a hissing sound close to the needle.

    ReplyDelete
  8. Hi Swagatam,
    Thanks for reply, tester is glowing near 2 or 3 mm distance.i have another question? you made your circuit straight 'I', but my circuit is 'u' shaped. That is 220v is near to the 4kv point.Is there any problem with that? And I will hear sound when when neddle sparks to tester ? Right.

    Thanks

    ReplyDelete
  9. Hi Rakibul, then most probably your circuit is working, it doesn't need to be built straight, can be in any form..as long as its built correctly.

    hang your circuit somewhere on the wall switched ON for a couple of days, if the wall behind the circuit becomes blackish would confirm that the circuit is indeed responding well.

    ReplyDelete
  10. ...the hissing sound will be heard when you bring your ear about 1cm close to the needle point, a tester is not needed for this.

    ReplyDelete
  11. Did anyone (or can anyone) try what happens if you switch positive and negative voltage? That way, the device creates positive ions instead of negative ions. I'm very curious whether this way, it still removes dust/particles. In other words: Are most dust/particles in the air really positively charged?

    ReplyDelete
  12. the polarity of the diodes will need to be changed for acquiring positive ions....this will not clean the dust particles as effectively as with negative ions...

    ReplyDelete
  13. hello Swagatam Majumdar, whether this circuit can be made by the board or PCB, let me look good

    ReplyDelete
  14. hello robert, yes it can be made over a dot matrix PCB

    ReplyDelete
  15. Greetings. I also had success with building it in one try. I used copper to connect resistor to the needle. I have one question, can I remove one or two resistors from the end to get better result at my needle ?

    ReplyDelete
  16. thanks, removing the resistors will not impact the output emissions by much, the resistors are introduced to ensure maximum safety for the user from the mains.

    ReplyDelete
  17. ....the recommended capacitor type will not show any leaking sign, a wrong diode connection or a poor quality diode or a duplicate diode can also cause problems in the circuit

    ReplyDelete
  18. breadboarding won't be a good idea, the best way of doing it is probably by twisting the leads and connecting, as done in the prototype sample because this method will prevent any chance of cross component leakages.

    for me the design worked immediately after assembling, although I had assembled it on a PCB,

    check the diode quality also, a duplicate brand can affect the results seriously.

    ReplyDelete
  19. hola, es que yo ya hice el multiplicador de voltaje, pero no se que resistencia debo usar al inicio del circuito y si ese bombillo del principio es un led y de cuanto. tambien al final que hay 3M3 son resistencias cierto...de cuanto son?

    ReplyDelete



  20. Sí, es un multiplicador de tensión, la resistencia a la entrada es sólo para la descarga de todos los condensadores cuando el circuito está enchufado de la toma, esto es para evitar una descarga eléctrica al usuario de la descarga.

    los 3m3 resistencias ar todo cuarto wa nominal y MFR tipo 1%



    "hello, is it a voltage multiplier, but that resistance should not be used at the beginning of the circuit and if that is the principle bulb led and how much. Also at the end there are some resistance 3M3 ... how much are they?"

    Yes it is a voltage multiplier, the resistor at the input is just for discharging all the capacitors whenever the circuit is plugged out of the socket, this is to prevent an electric shock to the user from the discharge.

    the 3m3 resistors ar all 1/4 wa rated and MFR 1% type

    ReplyDelete
  21. Dearest Swagatam.

    Could one build the mirror image of this circuit in anti-parallel in order to take advantage of both halves of the AC waveform? Right now it is only using the Positive half, and blocking the negative half...

    Thanks,
    --Tom

    ReplyDelete
  22. Oh.. I see, it is only using the negative half..... Gotcha, My mistake.... how could we invert the positive have of the AC wave to make use of it, I wonder?

    ReplyDelete
  23. Dearest Swagatam.

    I'm estimating that for USA 110V mains, you would need 70 Diodes and Capacitors to reliably attain 4kV. Our Mains voltage varies slightly, here, from 108 to 125, but 70 should do ok for even 108.

    Thanks,
    --Tom

    ReplyDelete
  24. Dearest Tom, the above circuit has been purposely designed in the shown manner (negative polarity) so that it generates negative ions which is considered to be beneficial in many ways...if we change the polarity of the diodes it will start producing positive ions which might be of no use, in fact harmful for the environment.

    ReplyDelete
  25. yes for 110V supply , you may need to double the number of diodes and the capacitors.

    ReplyDelete
  26. Dear Sir,
    I have made this circuit using .01 uF polyester Caps and IN4007 diodes. But I could not feel any sound or cooling effect at the needle tip. I have checked all the connections again and again. I have used 3mm SS Pins 10 Nos. at the end. I made the circuit with 30 caps. could you tell me where I might have gone wrong? The neon at the beginning is glowing. Is there any other way that we can check the emission of Ions? Kindly reply.

    ReplyDelete
  27. Dear Sarma,

    the possible reasons could be either a wrongly selected capacitor specification or a wrongly connected diode....a faulty diode can also prevent the circuit from functioning normally.

    most probably the capacitor could be of a wrong type...

    an alternative way of checking is by keeping a line-tester around 1cm close to the tip of the emitter

    ReplyDelete
  28. Dear Sir,

    Thank you very much for your immediate reply. I want to send you the pictures of my circuit. kindly let me know how to send the pictures. or you can give me your mail address. my mail id is sarma.challa@gmail.com.

    ReplyDelete
  29. Dear Sarma, you can send it to:

    admin (at) homemade-circuits.com

    ReplyDelete
  30. Dear sir,
    I have tested at the tip of the pin and current is coming. But there is no sound or light at the tip. I have used 30 nos 10nf 630V polyester capacitors and 1N4007 diodes. I checked all the diodes for continuity and confirmed that there is no continuity in the diodes. I have sent you the picture also. Is there any other way to check whether the ionizer is working or not?

    ReplyDelete
  31. Dear Sarma,

    if there's no mild hissing sound, or fishy smell or light on a line-tester close to the tip of the emitter then it means your circuit is not working.

    I saw the image sent by you, the capacitor specification looks OK but I could not see how you might have connected all the 30 diodes and the caps.

    please repeat the assembly using new components and this time do it exactly as per the layout of the shown diagram, meaning you must connect all the capacitors and the diodes exactly in the manner indicated in the diagram....or you can simply make it by twisting and soldering the parts just as Mr.Adnan has done in his prototype.

    ReplyDelete
  32. Dear sir,
    I have sent you the pictures of the circuit. I have checked the voltage at each capacitors. Almost at all the capacitors the voltage is around 230v (from mains to each capacitors). Seems some mistake somewhere. Kindly advice.

    Thanks

    ReplyDelete
  33. Dear Sarma,

    measuring the voltages is not required and it won't help, there's no easy way to troubleshoot it expect checking the polarities and the quality of the components.

    you'll have to assemble it again without using a PCB, as Mr. Adnan has done in the shown prototype.

    ReplyDelete
  34. ...I have seen the picture that you sent recently, and it's constructed as I suggested above, but I cannot see the emitter pin??

    connect a sharp, very sharp emitter pin via a a few 2m2 resistors and take your ear close to it in a silent environment....you should be able to hear a low hissing sound...please check it

    ReplyDelete
  35. Dear sir,
    I have connected the emitter pin. But if the AC power is reversed 40V current is coming to the pin. I cannot hear any sound from the pin. Can you suggest me anion tester circuit with LED? I have checked all the capacitors before connecting. One more thing.... I have checked the voltage from capacitor to capacitor. At the. Second one it is 60v 2nd to 3 Rd 30v and at 5 th it is showing 0v. That means the voltage is going to negative? What ever it is, finally I could not confirm that the circuit is working. Can I get a build circuit from you?

    Regards
    Ch M S SARMA

    ReplyDelete
  36. Dear Sarma,

    AC power does not have a polarity, no matter how you connect it to the circuit, there will no difference in the result...the circuit will continue to generate the negative ions.

    I made this unit when I was just 17 years old, and I did not have any trouble in making it work immediately.

    I built this the second time recently around 5 years ago, again I could make it work successfully but only at the second attempt, because in the first attempt I used low quality capacitors and it failed to produce any results, then I changed the capacitors with good ones and could instantly see the unit work.

    You can witness the prototype images in this website article:

    www.brighthubengineering.com/diy-electronics-devices/78220-simple-room-air-ionizer-and-purifier/

    here I have also shown the image of the prototype which failed to work due to bad capacitors (blue in color)

    I might have the working model still lying somewhere in my junk box, but due to lack of time it won't be possible for me to upload a video here...

    ReplyDelete
  37. Dear Sir,

    Thank you very much for your co-operation. I have a small doubt. The voltage at the final connection will be 6kV, which will generate negative ions. But we are reducing the voltage to some 40v with 2.2M resistance. will the pin, which is having a voltage of 40v will generate ions? else, can we connect the pins directly without using resistance?

    Regards,

    CH M S SARMA

    ReplyDelete
  38. Dear Sarma,

    who says it's reduced to 40V?? the tip of the 2m2 resistors will be also around -4kV (not 6kv)...but at extremely low current....resistance is required to prevent high current and electric shock at the emitter

    ReplyDelete
  39. Dear Sir,
    Should this circuit also work with 0.1uF capacitor? (same type and voltage as yours)
    Thanks!

    ReplyDelete
  40. Dear Andre, 0.1uF will produce higher current which may not be recommended for an ionizer because that can alter the specified health benefit results in an adverse way...

    but it will work.

    ReplyDelete
  41. Dear Sir,

    Can we increase the capacitor power and reduce the number of Capacitors? because I want to build a compact one.

    Thanks

    CH M S SARMA

    ReplyDelete
  42. What exactly do you want a build? If you are interested to make a room ionizer then you should make the design that's shown above without any changes, if you are planning to build a high voltage generator in that case you can try the idea that you have mentioned.

    ReplyDelete
  43. Good day sir, i just want to ask if there will be a problem if i dont follow the way the components are connected. I want to try this for my project but i need to apply a pcb design for it. Thanks !

    ReplyDelete
  44. Menardo, it's recommended to align and connect the parts precisely in accordance with the diagram, otherwise there could be a possibility of a mistake and confusions

    ReplyDelete
  45. i have another question sir. is this ionizer also neutralize the odor in the air ? thanks again sir.

    ReplyDelete
  46. yes it'll if many are employed...

    ReplyDelete
  47. I have another question sir. is it okay if i used 5 needles for this project ?

    ReplyDelete
  48. 5 needles will divide the voltage into 5....that would do no good to the results...it's better to use a single needle

    ReplyDelete
  49. If i use less caps (to increase voltage), and use more needles (how about 3),
    than, i can gain my scheme till 12 kV and in result (12 kV / 3 needles = 4 kV per needle).
    Is it correct? or i didnt understand the shematic till end?

    ReplyDelete
  50. sorry that's not possible...Google "Cockroft-Walton Ladder Network" for learning more about the concept

    ReplyDelete
  51. Sir, Ita really usful one but how to check it is working?

    ReplyDelete
  52. I have explained it in the article and the comments...please go through it comprehensively.

    ReplyDelete
  53. hi sir.thank you for this nice circuit. i have a question. can i use more needles to make more ions in this circuit?

    ReplyDelete
  54. Hi, No that's not possible, in fact increasing the number of needles will dilute the force of the ions and make the emission weaker..

    ReplyDelete
  55. Hi Sir,
    first of all congratulations for your web-site!!
    I have 2 questions for you:
    1-I'd like connecting a box with inside an electrified grid for purifying air: where do I connect the electrified grid to build an ionizing filter? after the 3 3M3 resistors?
    2-How long this circuit can stand on?Are there some risks for extended use?
    Thank you very much for your help.

    Gabri

    ReplyDelete
  56. Thanks Gabri,

    sorry i could not understand your first question??

    2) the circuit can last forever, just make sure to paint the whole PCB with a thick layer of oil paint after confirming its working....this is to safeguard the circuit from moisture, corrosion etc.

    ReplyDelete
  57. Thank you for your replay!
    I'm sorry for my english :(
    however, why did you put 3 resistors after the last diode?

    ReplyDelete
  58. the 3 resistors in series is to ensure 100% safety at the needle point against the minutest of electric shocks for the users.

    ReplyDelete
  59. sorry that may not be possible, because boosting a 9V low current to 4kv may ultimately be so weak that it won't initiate any ionization.

    ReplyDelete
  60. What will happened if i using capacitors with higher capacity for example 1uF rather than 0.01uF? Is that help to increase the efficiency?

    ReplyDelete
  61. probably the current will increase resulting in stronger ion generations....

    ReplyDelete
  62. Negative ions (anions) not only precipitate dust particles but also induce "good moods" in all living beings... plants, animals and humans alike. Natural sources of anions are waterfalls, fountains, rivers --in fact, any continuously running stream of water... like a shower.

    Cations (positive ions), however, induce the opposite effects. I did an experiment a couple of years ago --just inverted the diodes like Swagatam said-- and it induced headaches, anxiety and even breathing difficulties in everyone present. Not pleasant at all.

    ReplyDelete
  63. Question, Swagatam.... have you measured the anion output of your device?

    ReplyDelete
  64. thanks for the informations Amilcar, it's much appreciated!

    ReplyDelete
  65. No i did not measure the output, the only technical data I have is regarding the output voltage, which is around -4kv

    ReplyDelete
  66. what will happen if i choose 22uf capacitor? will the circuit not work?

    ReplyDelete
  67. the current at the output will increase, but I am not sure about the consequences...

    ReplyDelete
  68. I made the circuit based on your design. It does not produce any ion effect.
    I used a Line tester to see if the current is flowing, and the tester lights up on touching every diode connection as well as on the pin after the three 3M3 resistors.

    I have used Two-watt 3M3 resistors.

    How can i share the pics with you?

    ReplyDelete
  69. sir, what did you use to power the circuit since i can only see two wires connecting to it? thank you so much

    ReplyDelete
  70. sir, does the 10uf capacitor have to be of polyester material? i bought one of the same value (10 uf 630 volts, color red but its not polyester)

    ReplyDelete
  71. Maxine, the two wires go to the mains 220V or 120V source...

    ReplyDelete
  72. it's not 10uF, it 10nF...please make sure you read the instructions and the parts carefully before trying...

    ReplyDelete
  73. Sir, may I ask 'you can connect the body or the plates to ground or earth pin of your 3-pin socket' what will the best size an what type of plates to be used in a room of say 10x10 ft. Thanks.

    ReplyDelete
  74. A 4x4 feet will be enough...and it does not need to be metal or connected to earth.....

    ReplyDelete
  75. Greetings. Is it okay to use 0.01uF/630V PP capacitor? Does it affects the output?

    ReplyDelete
  76. Hi, 0.01uF/630V is fine, no it won't affect the output...

    ReplyDelete
  77. We already placed everything as the diagram shows. I alreay sent inages of our circuit. It was not working no cool breeze nor hissig noise. I don't know what mistake I made. I attached pictures to your email. Thanks!

    ReplyDelete
  78. either your connections has a fault or one of the parts or all the parts are not appropriately rated for this project.

    the diodes should have thick leads and good print on it, that will indicate an original 1N34007 diode...thin leads with faint print can be duplicates.

    capacitors should be preferably Philips made....others might or work might not work.

    check out this article which shows my working prototype in it and the explanation.

    www.brighthubengineering.com/diy-electronics-devices/78220-simple-room-air-ionizer-and-purifier/

    ReplyDelete
  79. Thanks very much for the reply.

    ReplyDelete
  80. the noddle end is harmful by touching

    ReplyDelete
  81. Hi Swagatam,
    I made this circuit today. I soldered the end to a needle. While testing with an Ion tester there is a pulsating glow indicating discharge of ion but, neither there is a hissing sound nor fish like smell, I could detect. It seems that the ion output is weak. Is it because I have used USHA PP 0.01 mfd 630v capacitors ?

    ReplyDelete
  82. Hi Partha, if you are getting a fluctuating light in your line tester without touching it with the needle then definitely your circuit is working.

    The hissing sound and the fish like smell can be too feeble and easily get diffused due to atmospheric disturbances, you must test these parameter inside a quite room with no breeze flowing, preferably switch OFF the fan while verifying them.

    ReplyDelete
  83. Thank you very much. It's indeed working. I could feel the cool breeze near the needle tip. Noe I will make another for my car and now I plan to use Philips capacitors. Can you suggest me a source for genuine electronic spares ? Thanks once again.

    ReplyDelete
  84. That's great, I am glad you could succeed with the project.

    all the reputed online electronic spare part stores are good, you can specify them the component type and make, and get the exact one delivered to you.

    ReplyDelete
  85. sir, how did you connect the sharp needle to the 2m2? just by electrical tape? thank you sir. (I am following the circuit diagram here: www.brighthubengineering.com/diy-electronics-devices/78220-simple-room-air-ionizer-and-purifier/#imgn_0)

    ReplyDelete
  86. Hi I tried making this but not working pls help..

    ReplyDelete
  87. What is the needle that is used and what is the material of the needle that is used?

    ReplyDelete
  88. Any sharp conductor will do, a normal sewing needle will also work...

    ReplyDelete
  89. A short length of coax (Arial cable) with the resistor connected to the outer braiding! Simply trim the insulation back at the other end to expose the copper braiding and straighten the ends out and you have got yourself an ion Arial! I did this by stripping the insulation fro the middle of a 6" piece pf cable and bending it to exit out of 2 holes to double the number of exit points for the ions .... it worked well ;)

    ReplyDelete
  90. Thanks for the Update, appreciate it.

    ReplyDelete
  91. Hello Sir,
    It is said that value of capacitors working voltage should be atleast twice the voltage it is exposed to. Here our circuit is being exposed to more than 2kV still is it okay to use 630V caps?

    ReplyDelete
    Replies
    1. Hi Kaustubh,

      the capacitors are actually supplied with 310V only by the AC peaks. The -4kv is developed through a multiplying effect of this 310V across each capacitor. But the final polarity of this 4kv becomes negative due to the oppositely configured diodes.

      Delete

Post a Comment