Skip to main content

Make this Amplifier Short/Overload Protection

The following article explains how to build a power amplifier short circuit or overload protection circuit for safeguarding loudspeakers from burning.

Why we need a Short Circuit Protection


While working with high power amplifier designs, two things become crucial, the protection of the amplifier and the protection of the speakers from an accidental over current influx.

Especially when the amplifier design involves costly mosfets, the design becomes specifically vulnerable to short circuits at the outputs.A short circuit at the output may be caused due to mishandling or ignorance from the part of the user.

Whatever might be the reason, the end results in the destruction of the precious mosfets inside the amplifier box.

The above mishap can be prevented by adding a small circuit for detecting a short circuit conditions at the outputs of an amplifier.

Simulation and Working


The given amplifier short/overload protection circuit diagram, shows an inexpensive design using just a single transistor for implementing the intended feature.

Normally a low value resistor is usually employed at the output of mosfet amplifiers, the current developed across this resistor can be well exploited for tripping a relay in case it exceeds the safe maximum current value.

The current threshold across the above resistor is sensed by an LED inside an optocoupler, which lights up the moment a short or overload conditions is sensed.

This instantly triggers the opto transistor which in turn switches ON the transistor driver and the associated relay mechanism.

Since the relay coils support the amplifier connection with the speaker output, disconnects the amplifier from the output connection, preventing the amplifier devices from a possible damage.

The capacitor at the base of the transistor keeps the transistor switched for a few seconds so that the relay does not oscillate randomly.


Amplifier Short/Overload Protection


Need Help? Please leave a comment, I'll get back soon with a reply!




Comments

  1. Hi,
    yes by mistake the positive connection is not shown in the diagram, a separate +12V should be connected to the link that connects the relay coil and the opto transistor.

    ReplyDelete
  2. not tested, but i am sure about it.

    yes it would also handle DC shorts across the speaker

    ReplyDelete
  3. Useful but I want the number of opto couple

    ReplyDelete
  4. OK it is useful circuit I want to know the number of opto couple
    Thank-you

    ReplyDelete
  5. Say the value of resistance 0.5 ohm iam not able to get in india

    ReplyDelete
  6. Sir thank you for reply but in India only 1 omhs is available can I use that one
    Thanks again

    ReplyDelete
  7. saravanan, please tell what is the max wattage limit do you prefer to implement? the resistor value will depend on this

    ReplyDelete
  8. 100 Watts 5.1 amplifier system it is designed by MOSFET IC I have changed my speaker for more than 8 times in 2 years
    Thankyou

    ReplyDelete
  9. for 100 watt you can use the following formula

    100/V = current

    therefore R = 1.5/current

    here V is your amp supply voltage

    ReplyDelete
  10. Sorry I can't understand which voltage
    Input to transformer is 220 volt and the output of the transformer is 24 volt the transformer current rateing is 5 amps
    Mean while I get only 1 ohmes in India
    Thank-you

    ReplyDelete
  11. the 0.5 ohm shown in the diagram will need to be calculated as explained using the formula in the previous comment.

    If your amplifier operating volatge is 24V then

    100/24 = 4.16

    R = 1.5/4.16 = 0.36 ohms

    wattage of resistor will be = 1.5 x 4.16 = 6.24 or a 10 watt will do.

    if you are getting 1 ohm then use two in parallel, in place of the indicated 0.5 ohm

    ReplyDelete
  12. .....two 1 ohm in parallel will do in place of 0.36 ohm

    ReplyDelete
  13. Thank you sir so I want to ready 6 circuit for 5.1 amplifier

    ReplyDelete
  14. you are welcome, yes that's right!

    ReplyDelete
  15. This circuit is new it OK can we use in4148 diode

    ReplyDelete
  16. Does anyone have a COMPLETE working circuit (including missing +12V to relay and opto) with all parts IDENTIFIED? Has anyone tested or built this circuit?

    ReplyDelete
  17. Sir,

    This circuit also prevent DC from amplifiers O/P? means, this circuit act as a speaker protection circuit?..

    How can calculate The resistor value in +75v -0- -75v 250W amplifier?


    ReplyDelete
  18. Rahul, yes you are correct, it will protect speaker from burning.

    for 75V 250 watt, the current limiter resistor can be calculated as

    250/75 = 3.33 amps

    R = 2/3.33 = 0.6 ohms

    watt = 2 x 3.33 = 6.66 or 10 watts

    ReplyDelete
  19. circuit NOT WORKING . . .

    ReplyDelete
  20. find the fault in your design, it will work

    ReplyDelete
  21. only detects DC at speaker out but not detects SHORT at speaker out.... optocoupler needs DC supply in order to work... how...in this circuit provides a SHORT protection, let's say a faulty (shorted)speaker wire to the amplifier?

    ReplyDelete
  22. did you check how much voltage is generated across the sensing resistor during the intended overload? did you check whether that voltage was actually sufficient or not for triggering the opto LED?

    the bridge is already present to convert the pulsating DC into rectified DC?

    check all the parameters above, and set up the resistor accordingly as per your overload threshold, the circuit will cut off the relay at the set point

    ReplyDelete
  23. Hi sir ...IAM planning to build your design what is the computation for my power amp are 1000 watts at 80 volt ....t.y.

    ReplyDelete
  24. Dondon, I have explained the formula in the article, please do it according to it...

    ReplyDelete
  25. Thank you sir ...I figure it out and calculate the exact value of the resistor.....t.y...

    ReplyDelete
  26. Fernando CavalleroMarch 28, 2018 at 11:36 AM

    Hi! Nice circuit. How do you decide to use 1.5 or 2 in the above formulas? That number means the voltage drop in the resistor to trigger the diode bridge. Thanks

    ReplyDelete
  27. Hi, thanks, I am glad you liked it! for the opto coupler to conduct optimally the current limiter resistor must develop a voltage equal to the sum of the forward voltages of two series diodes from the bridge and the LED inside the opto....the total may reach upto 2V minimum, that's why the value 2 needs to be used in the formula.

    ReplyDelete
  28. Hello brother my name is sandeep from Kerala,this circuit is suitable for PA class d amplifiers,? Brother ,amplifier is class d ,put Ac voltage is 56 voltage, amps is 16 amps, (secondary 14swg copper wire) amplifier maximum output is 2000 watts per channel ,my question is sir this circuit is suitable for this amp pls help me, vdc is 85 vdc

    ReplyDelete
  29. Hi Sandeep, you can use this concept for any amplifier or load, because it is designed only to sense the current level passing to the speaker wire. Just make sure to select the relay and the current sensing resistor accordingly....preferably replace the 1uF capacitor with a 100uF/25V for better delay and hold feature of the relay.

    ReplyDelete

Post a Comment