In this article we learn to make a simple ghost detector circuit or a paranormal being detector circuit for quickly investigating a possibly infested area.

Introduction


Do you believe in the existence of ghosts? Well some of you may answer positively while some may just nod their heads showing sheer skepticism regarding the issue. Whatever may be the reactions; nobody just can’t deny or ignore the responses delivered from the circuit explained in this article.

Here we are discussing a super simple yet super sensitive paranormal activity sniffer circuit, which can be effectively and possibly used for detecting ghosts or similar supernatural existence within a range of 10 meters.
Many of these circuits may be built and posted at definite intervals for securing a certain premise having a large area.

The circuit incorporates an alarm at the output which sounds immediately on detecting a paranormal intrusion. The circuit is ideally suited for areas that are prone to ghosts or likely of getting infested with similar para-natural sneakers.

WARNING 1 – THE DEVICE HAS BEEN TESTED WITH POSITIVE RESULTS AND IS PROVED TO BE EXTREMELY ACCURATE WITH THE DISCUSSED DETECTIONS. FOLKS WITH WEAK HEARTS OR TENDER PERSONALITY ARE ADVISED NOT TO GO ABOUT WITH THIS DEVICE, BECAUSE THE DEVICE NOT ONLY DETECTS BUT ALSO COINCIDENTALLY HAS THE ABILITY OF ATTRACTING THE PARABEINGS.

WARNING 2 – THE DEVICE CAN BE TESTED IN MORGUES, GRAVEYARDS, cemeteries etc. ZOMBIES ARE THE ONES WHICH ARE INSTANTLY DETECTED BY THIS DEVICE EVEN FROM DISTANCES MORE THAN 50 METERS. NO DOUBT CREATURE LIKE ZOMBIES WILL HATE THIS DEVICE….BEWARE.

Ghost Detection Concept


It has been found through experiments by many researchers that paranormal occupancy is strongly accompanied by RF disturbances ranging from a few Hertz to many Kilohertz.

These signals may be directly proportional to the hostile nature of the ghost. Zombies are found to be emitting the strongest signals and are therefore considered the most horrible among the lot.

The circuit of a ghost detector discussed here is typically configured for capturing the above RF emissions from these creatures and transforming them into more human understandable electronic indications.

Simulation and Working


A single versatile IC 324 is involved in the whole operation.

The IC is a quad opamp IC, meaning four opamps in one package.

Ghost Signal  Detector Circuit Diagram

Referring to the figure, the opamps can be seen configured as hi gain non inverting amplifiers.

All the opamps are configured as high gain signal amplifiers.

Tiny electromagnetic or RF disturbances which are typically found being generated during the presence of ghosts or paranormal activities are instantly picked up by the antenna of the circuit and are fed to the input of the first opamp stage at pin #9.

The signals get instantly amplified and are transferred to the subsequent stages for further amplification and enhancement.

The output of the last opamp is connected to an opto-coupler.

The optocoupler is a homemade type, incorporating an LED and an LDR fixed such that their emitting and detecting surfaces are placed face to face inside a light proof enclosure.

Here, the optocoupler is used for sensing the LED illumination that may occur when a certain paranormal activity is sensed.

The illumination produced over the LED is tracked by the LDR whose resistance falls with the LED light.

The fall in the resistance of the LDR activates the connected transistor at the output, which in turn actuates a buzzer or a horn indicating a possible ghost intrusion.

The whole circuit may be built over a small piece of vero-board and should be strictly operated with a 9 volt battery.

The whole system may be enclosed inside a plastic box with the antenna kept protruding out of the box.

Parts List


R1 = 100K,

R2 = 2M2,

R3, R4 = 1K,

C1 = 0.01uF ceramic

OP1 = LED/LDR assembly inside a light proof enclosure,

T1 = BC557,

B1 = Piezo Electric Buzzer

The above circuit was further modified by one of the enthusiasts Mr.Steven Chiverton, Let's learn more regarding the procedures from

Improved Ghost Detector Circuit


The circuit board i made a bit longer and included the ghost detector and at the end i did the circuit you submitted and made sure the photo transistor was opposite to the ghost detectors led one picture is your transistor buzzer circuit i made it separately to test then added it to the printed circuit board with the ghost detector on it.

Ghost Detector Prototype

Ghost Detector PCB

 



 

Here is another picture of your optocoupler buzzer circuit for the ghost detector,

i used matrix pins on the board like i do with many circuits.this eliminates the job of having to take the board out of the circuit to resolder wires , buzz wires go to buzzer and q1 wires go to phototransistor, and the positive and negatives go to switch that runs to 9 volts battery to positive buzzer to positive in and negative of buzzer marked with the minus symbol.



 

Hi Steven,

You have made this small circuit very special and all the effort you have put is amazing.

Thanks once again,

Swag

 



Thank you swagatam

its your circuit your ideas Ive upgraded thank you , now e have also the most sensitive lightening bolt detector for its size well have to test it out on a lightening bolt yet even though its very sensitive to the continuous sparking of the electric ignitor on the gas stove here it sounds awesome like receiving pulse rays well you should hear it different from just a hand held gas stove lighter with pezio electric sparks .

here is the talking electronics 6 million gain circuit it may be a good ghost detector circuit to and by changing the bc547 to the bc517 you get a 30 million gain circuit as featured on youtube as a spirit detector but i haven't found any ghosts yet to test it on

 



010jpg is the top view of the printed circuit board for the swagatam ghost detector circuit. 006 jpg is a close up of another ghost detector i just made notice the home made optocoupler using the fairchild photo transistor and led at each ends of a short length of black heatsink tubing.

ive changed the 10n ceramics to 10p to see what results i get when ive completed it allcouldn't resist the temptation to build another of your ghost detector circuits, so ill have backup in the case one fails

i hope you find some of these pictures better for your site or collection, this ones half finished so i have to do the wiring then put the rest of the box together as its a 3 peace one and maybe put the buzzer this time in a different area , etc etc i plan to build your ac sensor next to when i get to it ill email you all the details when i get to that one

 

LM324 based ghost detector circuit diagram

 

This is how i redraw circuits in a more simpler way using student version circuit maker , note the ic shape in its proper rectangle configuration , drawn using the trax maker tool and the pins stretched into there sizes, and shaped properly using the arrow tool, the numbering for the pins was done 1 number at a time using text tool function then dragged into the positions using the arrow in the program

 

READERS ARE REQUESTED TO SHARE THEIR EXPERIENCES WITH THIS DEVICE. A PHOTO OR A VIDEO PROOF WILL BE GREATLY APPRECIATED....

Need Help? Please send your queries through Comments for quick replies!