Testing and troubleshooting electronic project circuits requires a multimeter, so new hobbyists may feel interested to try the following homemade multimeter circuits as their next electronic project.

Using a Single Opamp 741


The few opamp based meter circuits such as Ohmmeter, voltmeter, ammeter are discussed below using the IC 741 and just a few other passive components.

Although multimeters are available plentifully in the market today, building your own homemade multimeter can be real fun.

Moreover the attributes involved can become thoroughly useful for the future electronic circuit building and testing procedures.

 DC Voltmeter Circuit using IC 741


DC Voltmeter Circuit using IC 741



A simple configuration for measuring DC voltages is shown above using the IC 741.

A couple of resistors Rx and Ry are introduced at the input in a potential divider mode at the non-inverting pin #3 of the IC.

The voltage to be measured is applied across the resistor R1 and ground.

Through proper selection of Rx and Ry, the range of the meter can be varied and different voltages can be measured.

AC Voltmeter Circuit using IC 741

AC Voltmeter Circuit using IC 741


In case you want to measure alternating voltages then the circuit illustrated above can become useful.

The wiring is similar to the above wiring, however the positions of Rx and Ry have changed and also a coupling capacitor comes into the scene at the inverting input of the IC.

Interestingly the meter here is now connected across a bridge network enabling the meter to display the relevant AC potentials correctly.

DC Ammeter Circuit using IC 741


Another circuit to measure Direct current or Amps using the IC 741 can be seen in the following figure.

The configuration looks pretty simple. Here the input is applied across the resistor Rz i.e. across the non-inverting input pin #3 of the IC and the ground.

The range of the meter can be simply varied by changing the value of the resistor Rz.

DC Ammeter Circuit using IC 741

Ohmmeter Circuit using IC 741


Resistors are one of the most important passive components which inevitably become an integral part of every electronic circuit.

A circuit may be virtually impossible to build without accompanying these amazing current controlling devices.

With so many resistors involved, a possible fault can always be on the cards.

Identifying them requires a meter – an Ohm meter. A simple design using the IC 741 is shown below just for the purpose.


Ohmmeter Circuit using IC 741



Unlike most of the analogue designs which tend to have a rather non-linear behavior, the present design very efficiently tackles the problem to produce a perfectly linear response with the corresponding measurements.

The range is pretty impressive, it can measure values of resistors right from 1K up to a staggering 10 M.

You may go on to modify the circuit for enabling the measurement of more extreme values.

The range is selected by moving the rotary switch switch into the relevant positions.

How to Calibrate the Meter Circuits


Calibrating th instrument is simple and is done with the following points: Adjust the selector switch to the “10K” position.

Trim the base preset of the transistor until its emitter voltage shows exactly 1 volt (measure using a digital multimeter.) Next, Fix an accurately known 10 K resistor into the measuring slot.

Adjust the trimmer associated with the moving coil meter until the meter shows a full scale deflection.

All the circuits discussed above use dual supply voltages. The meter used is a moving coil type and is specified as 1mA FSD.

The preset across the pins 1, 4 and 5 of the IC 741 used for this homemede multimeter is used for adjusting the initial condition meter to exactly zero.


 Relevant Values of Rx and Ry


The following are the values of the resistors required for varying the range of the respective meters.


DC Voltmeter

Rx--------------------Ry--------------------Meter
FSD

10M-----------------1K--------------------1
KV

10M-----------------10K-------------------100V

10M-----------------100K------------------10V

900K----------------100K------------------1V

NIL-------------------100K-----------------0.1V


DC AMMETER

Rz--------------------Meter
FSD

0.1-------------------1A

1---------------------100mA

10-------------------10mA

100-----------------1mA

1K-------------------100uA

10K-----------------10uA

100K---------------1uA


AC VOLTMETER

Ry---------------------Rx-------------------Meter
FSD

10K-------------------10M----------------1KV

100K-----------------10M----------------100V

1M-------------------10M-----------------10V

1M--------------------1M------------------1V

1M--------------------100K----------------100mV

1M--------------------10K------------------10mV

1M--------------------1K--------------------1mV



A request from one of the keen followers of this blog:

Hi Swagatam

Is it possible to design a small circuit module which can be used with a multimeter to measure minimum/maximum voltage of a fluctuating signal at any point of a circuit under observation.

For example, we can switch a toggle switch in our module at MIN position and measure the voltage at point (A). The volts shown by the multimeter would be LOWEST voltage of the signal.

And when the toggle switch is positioned at MAX, and the voltage is measured again at point (A) the meter will show the HIGHEST voltage of the signal.

The Design






Need Help? Please send your queries through Comments for quick replies!